News » Routing Table

Cisco CCNA CCNP Certification Exam Tutorial: Dialer Watch Computers Articles | June 18 Cheap Jerseys China , 2006
Dialer Watch is an important topic on your Cisco certification exams, but there are common errors you must avoid in order to pass the exams. Learn all about Dialer Watch from Chris Bryant, CCIE #12933.


Dialer Watch is a vital part of your CCNA and CCNP studies, particularly for the BCRAN exam, but it's one of the most misunderstood technologies as well. To help you pass the CCNA and CCNP certification exams, here's a detailed look at Dialer Watch.


Dialer Watch allows you to configure a route or routes as "watched" when the watched route leaves the routing table and there is no other valid route to that specific destination Cheap Jerseys , the ISDN link will come up. In the following example, R1 and R2 are connected by both a Frame Relay cloud over the 172.12.123.0 24 network and an ISDN cloud using the 172.12.12.0 24 network. The routers are running OSPF over the Frame cloud, and R1 is advertising its loopback of 1.1.1.132 as well as an Ethernet segment, 10.1.1.024, via OSPF. R2 has both of these routes in its OSPF table, as shown below.


R2#show ip route ospf



1.0.0.032 is subnetted Wholesale Authentic Soccer Jerseys , 1 subnets



O 1.1.1.1 [11065] via 172.12.123.1, 00:00:07, Serial0



10.0.0.024 is subnetted, 1 subnets



O 10.1.1.0 [110128] via 172.12.123.1, 00:00:08, Serial0


We want R2 to place a call to R1 if either the loopback or Ethernet networks leave R2's routing table Wholesale Soccer Jerseys , but we don't want to have to depend on interesting traffic. That dictates the use of Dialer Watch.


First, configure the list of watched routes with dialer watch-list. Only one of the watched routes needs to leave the routing table for the ISDN link to come up. In this example, R2 will watch both routes from its OSPF routing table.


Be careful with this command. The entries here need to match exactly the routes and masks being watched. Dialer watch-lists use subnet masks, not wildcard masks.


R2(config)#dialer watch-list 5 ip 10.1.1.0 255.255.255.0



R2(config)#dialer watch-list 5 ip 1.1.1.1 255.255.255.255


Configure the dialer watch-group command on the BRI interface, AND frame map statements for the watched routes. As with dialer-list and dialer-group, the group number referenced in the dialer watch-group command must match the number assigned to the dialer watch-list.


The Dialer Watch configuration will not work without frame map statements for each watched route. I repeat this because this is the step a lot of people leave out.


R2(config)#interface bri0



R2(config-if)#dialer watch-group 5


R2(config-if)# dialer map ip 1.1.1.1 255.255.255.255. name R1 5557777 broadcast



R2(config-if)# dialer map ip 10.1.1.0 255.255.255.0 name R1 5557777 broadcast


To test Dialer Watch Wholesale Jerseys China , the Serial0 interface on R2 will be shut down. Since we're running OSPF, the route table will be updated almost immediately and the ISDN link should come up right after that.


R2(config)#int s0



R2(config-if)#shut




01:12:47: %OSPF-5-ADJCHG: Process 1, Nbr 1.1.1.1 on Serial0 from FULL to DOWN, N
eighbor Down: Interface down or detached



01:12:47: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up



01:12:48: %SYS-5-CONFIG_I: Configured from console by console



01:12:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state
to up



01:12:49: %LINK-5-CHANGED: Interface Serial0 Wholesale Jerseys , changed state to administratively
down




01:12:50: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state
to down



01:12:53: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 5557777 R1


Within five seconds, the ISDN link is up. show dialer verifies that Dialer Watch is the reason the line was brought up.


R2#show dialer


BRI0 - dialer type = ISDN


Dial String Successes Failures Last DNIS Last status



5557777 2 0 00:00:11 successful



0 incoming call(s) have been screened.



0 incoming call(s) rejected for callback.


BRI0:1 - dialer type = ISDN



Idle timer (120 secs), Fast idle timer (20 secs)



Wait for carrier (30 secs), Re-enable (15 secs)



Dialer state is data link layer up



Dial reason: Dialing on watched route loss



Time until disconnect 108 secs



Connected to 5557777 (R1)

A final note regarding Dialer Watch ... it will not work with RIP, but will with all our other dynamic IGPs (IGRP Cheap Authentic Soccer Jerseys , EIGRP, OSPF). Article Tags: Ccnp Certification, Dialer Watch, Watched Route, Routing Table, Isdn Link Cheap Soccer Jerseys Wholesale , Watched Routes, Interface Bri0:1




Bancassurance in Switzerland: Life, Non-Life and Creditor Insurance is about the distribution of insurance products through banks and other lending institutions in Switzerland. Types of insurance considered are: investment-related life insurance and retirement savings; risk life insurance, critical illness insurance and income protection insurance; accident insurance, medical expenses insurance and health hospital cash plans; personal motor insurance and household insurance; and creditor insurance for mortgages, consumer finance and credit cards. Based on a survey of 69 organisations Cheap Soccer Jerseys Free Shipping , it identifies 169 bancassurance distribution initiatives across these types of insurance, and highlights the operating models and product providers used in the vast majority of cases. Moreover, it analyses these bancassurance agreements in terms of 鈥榳eighted partnerships鈥?which take into account the size of the retail customer base of the banking institutions distributing these policies, th. Cheap NHL Jerseys Cheap College Hockey Jerseys Cheap Authentic MLB Jerseys Cheap Jerseys China Wholesale Cheap Hockey Jerseys Cheap Football Jerseys Cheap Jerseys From China Cheap New NHL Jerseys Cheap Soccer Jerseys China Cheap Hockey Jerseys